Chucks Mounted on Rotary Tables

Item Code: NESCR-65.3R
Description:

• A very high quality low profile 75 mm (3 Inches) Rotary Table with 4 slots supplied with a 3 jaw Self Centering 65 mm Lathe Chuck for Milling Machine. 
• Overall height of the table is 42 mm (without chuck) & 95 mm (with Chuck)
• The worm gear ratio is 36: 1 which means 1  rotation of handle will turn the table by 10 degrees.
• The hand wheel is in 10 min division and can be set at 0.
• It is supplied with a Mounting Back plate, a set of T-nuts apart from Chuck Mounting on the Rotary Table.
• The table can be mounted both horizontally and vertically.
• An excellent finish quality product with wrinkle paint for a long life !!

Item Code: NESC4R-70.4
Description:

Description of 4″ (100 mm) Rotary Table

• Designed for smaller milling machines.
• Table diameter 100 mm
• Table is graduated 360 Degrees.
• Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees.
• Center Height in vertical position: 2-1/16″ (50 mm approx)
• Hand wheel is graduated in divisions of 10 min & can be set to zero.
• Can be mounted both in Horizontal & vertical position.

Item Code: NETC-RRT3C80-4
Description:

Description:

• A very high quality low profile 3 Inches ( 80 mm) Rotary Table with 4 slots supplied with a 4 jaw Independent 80 mm Lathe Chuck for Milling Machine. 
• Overall height of the table is 1 5/8″ (without chuck)
• The worm gear ratio is 36: 1 which means 1  rotation of handle will turn the table by 10 degrees.
• The hand wheel is in 10 min division and can be set at 0.
• It is supplied with a Mounting Back plate, a set of T-nuts apart from Chuck Mounting on the Rotary Table.
• The table can be mounted both horizontally and vertically.
• An excellent finish quality product with wrinkle paint for a long life !

Item Code: NETC-TRT3C80-4
Description:

Description:

• A very high quality 75 mm (3 Inches) Rotary Table with 4 slots supplied with a 4 jaws 80 mm Independent Lathe Chuck for Milling Machine. 
• The table can tilt and lock into any position from 0 to 90 degrees.
• The worm gear ratio is 36: 1 which means 1  rotation of handle will turn the table by 10 degrees.
• The hand wheel is in 10 min division and can be set at 0.
• It is supplied with a Mounting Back plate, a set of T-nuts apart from Chuck Mounting on the Rotary Table.
• The table can be mounted both horizontally and vertically.
• An excellent finish quality product with wrinkle paint for a long life 

Item Code: NEBSCR-65.3
Description:

3” (75 mm) Tilting  Rotary Table with a 65mm- 3 Jaw Self Centering Lathe Chuck for Milling Machine

This Whole Package Includes below : –

• 1 Pc. 3” / 75 mm Tilting Rotary table
• 1 Pc. of a high quality 65 mm 3 Jaw self centering Chuck
• 1 Pc. of a back plate which has holes in a manner that it can be  fitted on to a 3 slot as well 4 slot Rotary table.
• 3 set of T nut to clamp / tighen the Back Plate with the Tee slots of the Rotary Table.

Item Code: NESC6R-150.4
Description:

Description of HV6 Rotary Table:

• Rotary Table Diameter :150 mm (6″)
• Overall Height without chuck: 80 mm ( 3-1/4″) 
• Centre Height in Vertical Position: 105 mm
• Worm- Gear Ratio- 1:90, which means that the 1 handle rotation shall turn the table by 4 Degrees.
• Table Graduated 360 Degrees, Resettable Dial & Handwheel graduated in seconds. Vernier scale is calibrated to 10 seconds.
• Centre Bore of the Table: 2 MT
• 2 Oiling Points for a direct lubrication of the Table for longer life & better performance.
• Can be clamped in Horizontal as well Vertical Position.

Description of the 150 mm -4 Jaws Independent Chuck

• A low profile chuck of diameter 150 mm (same as the table diameter) which can be fitted without any Back Plate to the Table.

Item Code: NETC-TRT4C65
Description:

4” (100 mm) Tilting  Rotary Table with a 65mm- 3 Jaw Self Centering Lathe Chuck for Milling Machine

This Whole Package Includes below : –

• 1 Pc. 4” / 100 mm Tilting Rotary table
• 1 Pc. of a high quality 65 mm 3 Jaw self centering Chuck
• 1 Pc. of a back plate which has holes in a manner that it can be  fitted on to a 3 slot as well 4 slot Rotary table.
• 3 set of T nut to clamp / tighen the Back Plate with the Tee slots of the Rotary Table

Item Code: NESC4R-100.3
Description: 

Description of 4 Inches (100 mm) Rotary Table

• Designed for smaller milling machines.
• Table diameter 100 mm
• Table is graduated 360 Degrees.
• Worm Gear Ratio -1:36, which means that the 1 handle rotation shall turn the table by 10 Degrees.
• Center Height in vertical position: 2-1/16″ (50 mm approx.)
• Hand wheel is graduated in divisions of 10 min & can be set to zero.
• Can be mounted both in Horizontal & vertical position.

Item Code: NESC5R-100.3
Description:

Description of the HV5 Rotary Table:

• Rotary Table Diameter :127 mm (5″)
• Overall Height : 87 mm ( 3-7/16″)
• Centre Height in Vertical Position: 90 mm
• Worm- Gear Ratio- 1:72, which means that the 1 handle rotation shall turn the table by 5 Degrees.
• Tee -Slot width ( Top of the Table) : 12 mm
• Table Graduated 360 Degrees, Resettable Dial & Handwheel graduated in seconds. Vernier scale is caliberated to 10 seconds.
• Centre Bore of the Table: 2 MT
• Can be clamped in Horizontal as well Vertical Position.